TNC Cable

TNC Cable Distributors, Suppliers in Taiwan.
We are experience TNC Cable supplier, exporter in Taiwan. Due to better satisfy the needs of customers, we will keep on promoting our skills of products and good service to all of them.
To shop high quality TNC Cablein the best price. Things you need to know about TNC Cable from a company, supplier in Taiwan
our

TNC Cable

have been widely accepted by customers from all over the world. Guarantee to our customers the best level of service offering capability, punctuality and quality bring lots of praise from our clients and win international markets.
  • TNC Cable - TNC Connector
TNC Cable
Model - TNC Connector
TNC FOR LMR600 CABLE / TNC FOR RG58U CABLE / TNC FOR RG-174U CABLE / TNC FOR LMR400 CABLE / TNC FOR 1.32 CABLE

TNC (Threaded Neill-Concelman) connectors are a threaded version of BNC connectors. The interface specification for TNC and many other connectors is referenced in US Military Standard MIL-STD-348. The connector has a 50 ohm impedance and operates best in the 0-11 GHz spectrum. It has better performance than BNC connectors at microwave frequencies.
Most TNC connectors are the 50 ohm type even for use with other impedance coaxial cables, but there are also 75 ohm series available that provide a good SWR around 1 GHz. These can be identified by the reduced amount of dielectric at the mating end.
Reverse Polarity TNC (RP-TNC) connectors have been widely used by Wi-Fi device manufacturers to comply with specific local regulations, such as those from the FCC, designed to prevent consumer connections from exhibiting gain and thus violating compliance antenna. The FCC finds the RP-TNC acceptable in preventing consumers from replacing the antenna.
  • Various RF cable options available:RG316 / RG174 / RG58 / RG178 / RG223.
  • If you can't find the connector you need, please contact us.
Enquiry Now
Products List
BNC STRAIGHT PLUG CLAMP FOR RG-58U / BNC STRAIGHT JACK CRIMP FOR RG-174U / BNC R/A PLUG CRIMP FOR RG-58U / BNC JACK BULKHEAD CRIMP FOR RG-174U / BNC STRAIGHT PLUG CRIMP FOR RG-174U / BNC JACK BULKHEAD CRIMP FOR RG-58U BNC (Bayonet Neill-Concelman) connectors are miniature quick connect/disconnect RF connectors for coaxial cables. The interface specification for BNC and many other connectors is referenced in US Military Standard MIL-STD-348. It has two bayonet lugs on the female connector; full mating is achieved by a quarter turn of the connecting nut. BNC connectors are used with micro-to-subminiature coaxial cables in radio, television and other RF electronic equipment, test instruments and video signals. BNC connectors are manufactured to match the cable characteristic impedance of 50 ohms or 75 ohms. They are typically used for frequencies below 4 GHz and voltages below 500 volts. Typically, the male connector is installed on the cable and the female connector is installed on the panel on the device. Cable connectors are usually designed to be installed by crimping using special power or hand tools. Use a wire stripper, which strips the outer jacket, shield braid, and inner dielectric to the correct length in one operation. Various RF cable options available:RG316 / RG174 / RG58 / RG178 / RG223. Various connector options available:SMA / SMB / MCXX / MCX / BNC / TNC. If you can't find the connector you need, please contact us.
MMCX TO FOR RG-174U / MMCX STRAIGHT PLUG EDGE CARD MOUNT MMCX PLUG PC BOARD MOUNT / MMCX STRAIGHT JACK PC BOARD MOUNT MMCX STRAIGHT JACK EDGE CARD MOUNT MMCX (miniature coaxial) connectors are coaxial RF connectors similar to MCXs, but smaller. They comply with the European CECC 22000 specification. MMCX connectors are rated for 500 mating cycles. The connector has a locking spring mechanism that allows 360 degree rotation and typically has a 50 ohm impedance. They provide broadband capabilities from DC to 6 GHz. MMCX connectors are most commonly found on Wi-Fi PCMCIA cards as antenna connectors, or as connectors for external GPS antennas on small devices such as PDAs or GPS receivers. They are also used by various brands of in-ear monitors to connect cables to individual headphones. This allows cables to be replaced or swapped. Various RF cable options available:RG316 / RG174 / RG58 / RG178 / RG223. Various connector options available:SMA / SMB / MCXX / MCX / BNC / TNC. If you can't find the connector you need, please contact us.
SMA FOR RG58U CABLE / SMA FOR RG174U CABLE / SMA FOR LMR400 CABLE / SMA FOR H155 CABLE / SMA FOR RG402U CABLE / SMA FOR 1.13 CABLE The interface dimensions for SMA connectors are listed in the US military regulation MIL-STD-348. SMA connectors use a 1/4 inch diameter threaded sleeve with 36 threads per inch. The center pin of a standard polarity SMA male connector is surrounded by a cylinder with internal threads, and the center sleeve of a standard SMA female connector is surrounded by a cylinder with external threads. There are also reverse polarity ("RP") SMA connectors with interchangeable center pins and sleeves; browse RP products for a more comprehensive description. Our high-quality SMA connectors are rated for up to 500 mating cycles, but to achieve this, the correct torque value must be used when connecting. Flats are also provided on the cable side of the connector assembly so that a second wrench can be used to prevent it from rotating and damaging the connector to the cable. Various RF cable options available:RG316 / RG174 / RG58 / RG178 / RG223 / RG402 etc.. Various connector options available:SMA / SMB / MCXX / MCX / BNC / TNC. If you can't find the connector you need, please contact us.